|
|
Mubychem Group, established in
1976, is the pioneer manufacturer of Zinc Chloride, Ammonium
Chloride, Calcium Chloride, Potassium Chloride, Sodium Acetate,
Sodium Thiosulphate, Pharmaceutical, Fragrance & Flavor chemicals in
|
For Translating this page in your language use this translation tool (Refresh if the tool is not seen). |
Buy Zinc Stearate; Door Delivery
British Pharmacopoeia 2009
Zinc Stearate BP
Zinc Stearate British Pharmacopoeia
(C17H35CO2)2Znıı632ıı557-05-1
Action and use
Excipient.
DEFINITION
Zinc stearate [(C17H35COO)2Zn; Mr 632] may contain varying proportions of zinc palmitate [(C15H31COO)2Zn; Mr 576.2] and zinc oleate [(C17H33COO)2Zn; Mr 628].
Content
10.0 per cent to 12.0 per cent of Zn.
CHARACTERS
Appearance
Light, white or almost white, amorphous powder, free from gritty particles.
Solubility
Practically insoluble in water and in anhydrous ethanol.
IDENTIFICATION
A. Freezing point (2.2.18): minimum 53 °C, determined on the residue obtained in the preparation of solution S (see Tests).
B. Neutralize 5 ml of solution S to red litmus paper R with strong sodium hydroxide solution. The solution gives the reaction of zinc.
TESTS Solution S
To 5.0 g Zinc Stearate add 50 ml of ether R and 40 ml of a 7.5 per cent V/V solution of cadmium- and lead-free nitric acid in distilled water. Heat under a reflux condenser until dissolution is complete. Allow to cool. In a separating funnel, separate the aqueous layer and shake the ether layer with 2 quantities, each of 4 ml, of distilled water R. Combine the aqueous layers, wash with 15 ml of ether R and heat on a water-bath until ether is completely eliminated. Allow to cool and dilute to 50.0 ml with distilled water (solution S). Evaporate the ether layer to dryness and dry the residue at 105 °C.
Appearance of solution
Solution S is not more intensely coloured than reference solution.
Appearance of solution of fatty acids
Dissolve 0.5 g of the residue obtained in the preparation of solution S in 10 ml of chloroform R. The solution is clear and not more intensely coloured than reference solution.
Acidity or alkalinity
Shake 1.0 g with 5 ml of ethanol (96 per cent) R and add 20 ml of carbon dioxide-free water and 0.1 ml of phenol red solution R. Not more than 0.3 ml of 0.1 M hydrochloric acid or 0.1 ml of 0.1 M sodium hydroxide is required to change the colour of the indicator.
Acid value of the fatty acids
195 to 210.
Chlorides
Maximum 250 ppm.
Sulphates
Maximum 0.6 per cent.
Cadmium
Maximum 5.0 ppm.
Atomic absorption spectrometry
To pass the test
Lead
Maximum 25.0 ppm.
Atomic absorption
To pass the test
Zinc Stearate USP-NF
Zinc Stearate
Octadecanoic acid, zinc salt.
Zinc stearate [557-05-1].
Zinc Stearate is a compound of zinc with a mixture of solid organic acids obtained from fats, and consists chiefly of variable proportions of zinc stearate and zinc palmitate. It contains the equivalent of not less than 12.5 percent and not more than 14.0 percent of ZnO.
Identification—
A: Mix 25 g Zinc Stearate with 200 mL of hot water, add 60 mL of 2 N sulfuric acid, and boil until the fatty acids separate as a transparent layer. Cool the mixture, and remove the solidified layer of fatty acids: a portion of the water layer responds to the tests for Zinc.
B: Place the separated fatty acids obtained in Identification test A in a filter wetted with water, and wash with boiling water until free from sulfate. Collect the fatty acids in a small beaker, allow to cool, pour off the separated water, then melt the acids, filter into a dry beaker while hot, and dry at 105 for 20 minutes: the fatty acids congeal at a temperature not below 54.
Arsenic— The limit is 1.5 ppm.
Lead— The limit is 0.001%.
Alkalies and alkaline earths— Mix 2.0 g with 50 mL of water, add 10 mL of hydrochloric acid, boil until the solution is clear, filter while hot, and wash the separated fatty acids with about 50 mL of hot water. Render the combined filtrate and washings alkaline with 6 N ammonium hydroxide, add ammonium sulfide TS to precipitate the zinc completely, dilute with water to 200 mL, mix, and filter. To 100 mL of the clear filtrate add 0.5 mL of sulfuric acid, evaporate to dryness, and ignite to constant weight: the weight of the residue does not exceed 10 mg (1.0%).
More from Zinc Stearate Manufacturer at:
MUBY CHEMICALS
S-8, SARIFA MANSION, 2ND FLANK ROAD,
CHINCHBUNDER, MUMBAI 400009, INDIA.
TEL: (OFFICE) 91-22-23770100, 23726950,
23774610, 23723564. FAX: 91-22-23728264.
e-mail:
info@mubychem.com
Cell Call to Anmol: +91-9821870100 or Ambrish: +91-9821570100
Copyright and Usual Disclaimer is
Applicable.
Last updated
29 April, 2010
If I give you
“My Word” Nobody can undo it.
If I sign an
“Agreement” my Lawyer will undo it
|
Old Spice: Manufacturing since more than Three Decades: |
|||
|
Pharmaceuticals & Food Grade, IP BP USP FCC ACS Gr. of Chemicals mfd. by Anmol Chemicals: A.R. |
|||
|
Other Best Seller Products: |
|||